Media Presentation Button Panel B10, White
This product has been discontinued. Please contact Crestron True Blue Support at 1-888-CRESTRON for a replacement solution or more information.
A 3-gang, 10-button wall mount control panel with customizable backlit labeling, LED feedback, and volume control knob. Single-wire interface via PoE Ethernet or Cresnet®.
The MP-B10 is an enhanced pushbutton control panel designed for installation in a wall or podium. It can be used with any Crestron® control system or presentation switcher, and it provides a perfect complement to any Crestron MPC Media Presentation Controller. Available in white or black, the MP-B10 is constructed to handle the rigors of everyday use in a typical classroom, meeting room, lecture hall, or training facility.
Its 10 “hard key” buttons can be custom programmed to control any function, such as system power, input source selection, and lighting presets. Audio volume and other parameters are adjustable using the control knob and LED bargraph. Custom backlit labeling of each button is facilitated using an assortment of pre-printed labels or Crestron Engraver software.
A built-in IR receiver provides a gateway for RC-5 and Crestron compatible IR wireless remotes. An ambient light sensor is also included, which may be programmed to control the MP-B10’s backlight intensity and other customer functions. The MP-B10 can be powered through the network wiring using either Cresnet® or PoE (Power over Ethernet), requiring just one wire for operation.
Key Features
- Wall mount pushbutton control panel
- No programming required with select .AV Framework™ enabled switchers
- 10 programmable buttons with LED feedback
- Customizable backlit button labels
- Volume control knob and LED bargraph
- Built-in IR receiver and light sensor
- High-speed Ethernet or Cresnet® communications
- PoE or Cresnet network powered
- 3-gang wall box-mountable
| Communications |
| |
Ethernet |
10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, IEEE 802.3af and 802.3at Type 1 compliant |
| |
Cresnet® |
Cresnet slave mode |
| |
USB |
USB 1.1 device port for computer console (firmware update) |
| |
IR |
Built-in RC-5 compatible IR receiver |
| Connectors |
| |
NET |
(2) sets of (4) captive screw terminals;
Cresnet slave port with parallel pass-through |
| |
LAN PoE |
(1) 8-wire RJ45, female;
10Base-T/100Base-TX Ethernet port, Power over Ethernet compliant |
| |
Computer |
(1) USB Type B, female (behind front cover);
USB 1.1 computer console port for firmware update |
| |
Ground |
(1) flying lead, chassis ground wire |
| Controls & Indicators |
| |
Hard Keys |
(10) Programmable pushbuttons with backlit labeling |
| |
Feedback Indicators |
(10) Programmable red LEDs (1 per hard key) |
| |
VOLUME |
(1) Programmable continuous turn rotary encoder |
| |
Bargraph |
(1) Programmable red 5-segment LED bargraph |
| |
HW-R |
(1) Recessed miniature pushbutton for hardware reset |
| |
SETUP |
(1) Recessed miniature pushbutton (behind front cover) for setting up connection with the control system via Cresnet or Ethernet |
| |
LAN PoE (rear) |
(2) green LEDs, bottom LED indicates link status, top LED indicates Ethernet activity |
| Light Sensor |
| |
Photosensor, programmable for auto-dimming of the backlight and other functions |
| IR Receiver |
| |
Reception Frequency |
36 to 38 kHz IR |
| |
Formats |
Crestron format, RC-5 |
| |
Range |
Up to 50 ft line of sight (typical), dependent upon angle, obstructions, IR interference, and IR remote signal strength |
| Power Requirements |
| |
Cresnet Power Usage |
4 Watts (0.17 Amps @ 24 Volts DC) |
| |
Power over Ethernet |
IEEE 802.3at Type 1 (802.3af compatible) Class 2 (6.49W) PoE Powered Device |
| |
Note: If both PoE and Cresnet power are connected, power will be drawn from Cresnet. |
| Environmental |
| |
Temperature |
32° to 104°F (0° to 40°C) |
| |
Humidity |
10% to 90% RH (non-condensing) |
| |
Heat Dissipation |
14 BTU/hr |
| Enclosure |
| |
Faceplate |
Plastic, black or white, with polycarbonate label overlay |
| |
Chassis |
Plastic with metal mounting plate |
| |
Mounting |
Mounts in a 3-gang electrical box or mud ring, 2 inch (51 mm) or greater mounting depth recommended |
| Dimensions |
| |
Height |
4.50 in (115 mm) |
| |
Width |
6.70 in (171 mm) |
| |
Depth |
2.23 in (57 mm) |
| Weight |
| |
17 oz (475 g) |
Click
here to search product certificates.
Please select your region below to see the appropriate Advertised Pricing.