| Audio |
| |
- Typical of 3 mono amplifier channels:
|
| |
Input Signal Type |
Balanced or unbalanced analog line-level |
| |
Output Signal Type |
4/8 Ohm |
| |
Output Power |
120 Watts at 8 Ohms;
210 Watts at 4 Ohms;
420 Watts at 8 Ohms bridged (channels 1 and 2) |
| |
Damping Factor |
>100 |
| |
Protection |
Over Current, Over/Under Voltage, Over Temperature, DC Offset |
| |
Frequency Response |
20Hz to 20kHz ±0.5 dB |
| |
THD |
0.05% @ 1kHz, full rated power at 4/8 Ohms or 8 Ohms Bridged;
0.1% @ 20Hz to 20kHz, 120W at 8 Ohms;
0.2% @ 20Hz to 20kHz, 210W at 4 Ohms;
0.1% @ 20Hz to 20kHz, 420W at 8 Ohms Bridged |
| |
S/N Ratio |
>103 dB, A-weighted |
| |
Crosstalk |
>70 dB @ 1kHz |
| |
Gain |
23 dB with INPUT LEVEL control set at 12 o'clock nominal position |
| |
Input Sensitivity |
2.22 Vrms for rated output power with INPUT LEVEL control set at 12 o'clock nominal position |
| |
Input Detection Threshold |
40 mV RMS @ 1 kHz |
| |
Input Level Adjustment |
±10 dB from nominal |
| Connectors |
| |
G |
6-32 screw, chassis ground lug |
| |
INPUT CH 1 – 3 |
(3) 3-pin 3.5mm detachable terminal blocks;
Balanced/unbalanced line-level audio inputs;
Input Level: 5.3 Vrms maximum with INPUT LEVEL control set at minimum position;
Input Impedance: 24k Ohms balanced, 12k Ohms unbalanced |
| |
SPEAKER OUTPUT CH 1 – 3 |
(3) 2-pin 7.62mm 15A detachable terminal blocks;
4Ω/8Ω and 70/100V power amplifier outputs;
Wire Size: Terminals accept up to 14 AWG |
| |
REMOTE |
(1) 6-pin 3.5mm detachable terminal block;
Provides (3) remote control inputs; enables independent power control of each channel via local jumpers or remote contact closures;
inputs may be safely paralleled for group or global control |
| |
FUSE T6.3AH 250V |
Main fuse holder;
5x20 mm, 250V, 6.3AH, time-lag, high-rupture rated |
| |
100-240V~50/60Hz |
(1) IEC C14 male chassis plugs, main power input;
Mates with removable power cord (included) |
| Controls & Indicators |
| |
PWR |
(1) dual-color LED, green indicates ACTIVE state, yellow indicates STANDBY state |
| |
INPUT 1 – 3, SIGNAL |
(3) green LEDs, indicate signal presence on each corresponding channel |
| |
OUTPUT 1 – 3, CLIP |
(3) amber LEDs, indicate a clipping condition on each corresponding channel |
| |
OUTPUT 1 – 3, FAULT |
(3) red LEDs; indicate over-temperature, over-current, over or under power supply voltage, or DC offset condition on each corresponding channel |
| |
INPUT CH 1 – 3 LEVEL (rear) |
(3) Rotary input boost/attenuate adjustments w/center detent at nominal |
| |
ON/REMOTE/OFF (rear) |
(1) 3-position slide switch; selects between all channels powered on, all channels powered off, or remote control of each individual channel |
| Power Requirements |
| |
Main Power |
100-240 Volts AC, 50/60 Hz |
| |
Power Consumption |
85 Watts @ 8 Ohms, all channels driven at 1/8th output power;
126 Watts @ 4 Ohms, all channels driven at 1/8th output power;
32 Watts, all channels idle;
<1 Watt in standby |
| Environmental |
| |
Temperature |
41° to 104°F (5° to 40°C) |
| |
Humidity |
10% to 90% RH (non-condensing) |
| |
Heat Dissipation |
137 BTU/Hr @ 8 Ohms, all channels driven at 1/8th output power;
162 BTU/Hr @ 4 Ohms, all channels driven at 1/8th output power;
110 BTU/Hr, all channels idle;
<3.4 BTU/Hr in standby |
| Enclosure |
| |
Chassis |
Metal with black finish, vented top and sides, convection cooled |
| |
Front Panel |
Metal, black finish with polycarbonate label overlay |
| |
Mounting |
Freestanding or 1U 19-inch rack-mountable (adhesive feet and rack ears included) |
| Dimensions |
| |
Height |
1.70 in (44 mm) |
| |
Width |
17.28 in (439 mm);
19.0 in (483 mm) with rack ears |
| |
Depth |
10.34 in (263 mm) |
| Weight |
| |
8.3 lb (3.8 kg) |