| Video |
| Switcher |
2x1 auto-switching or manual, audio-follows-video, Crestron Auto-Locking® and QuickSwitch HD™ technologies |
| Scaler (HDMI Output) |
4K video scaler with intelligent frame rate conversion, Deep Color support, content-adaptive noise reduction, 3:2/2:2 pull-down detection and recovery |
| Input Signal Types |
HDMI with Deep Color and 4K (DVI and Dual Mode DisplayPort™ interface compatible2) on Input 1, DM Essentials with Deep Color and 4K on Input 2 |
| Output Signal Types |
HDMI with Deep Color and 4K (DVI compatible3) |
| Copy Protection |
HDCP 2.2 |
| Maximum Resolutions |
Common resolutions are listed below for the HDMI and DM Essentials inputs. |
Scan
Type |
Resolution |
Frame
Rate |
Color
Sampling |
Color
Depth |
| Progressive |
4096x2160 DCI 4K and 3840x2160 4K UHD |
24 Hz |
4:4:4 |
30 bit |
| 30 Hz |
4:4:4 |
24 bit |
| 30 Hz |
4:2:2 |
36 bit |
| 60 Hz |
4:2:0 |
24 bit |
| 2560x1600 WQXGA |
60 Hz |
4:4:4 |
36 bit |
| 1920x1080 HD 1080p |
60 Hz |
4:4:4 |
36 bit |
|
NOTES:
- Custom resolutions are supported at pixel clock rates up to 300 MHz.
- Interlaced video sources are not supported.
|
| Scaler Output Resolutions, HDMI |
Auto (EDID preferred);
1280x720p@50Hz (720p50);
1280x720p@60Hz (720p60);
1920x1080i@25Hz (1080i25);
1920x1080i@30Hz (1080i30);
1920x1080p@30Hz (1080p30);
1920x1080p@25Hz (1080p25);
1920x1080p@24Hz (1080p24);
1920x1080p@50Hz (1080p50);
1920x1080p@60Hz (1080p60);
3840x2160p@24Hz;
3840x2160p@25Hz;
3840x2160p@30Hz,;
4096x2160p@24Hz;
4096x2160p@25Hz;
4096x2160p@30Hz;
3840x2160p@50Hz;
3840x2160p@60Hz;
4096x2160p@50Hz;
4096x2160p@60Hz |
| Audio |
| Input Signal Types |
HDMI (Dual-Mode DisplayPort compatible2), DM Essentials |
| Output Signal Types |
HDMI, stereo analog |
| Digital Formats |
2-channel LPCM |
| Analog Formats |
Stereo 2-channel |
| Digital-to-Analog Conversion |
24-bit 48 kHz |
| Output Impedance |
200 Ω balanced;
100 Ω unbalanced |
| Maximum Output Level |
4Vrms balanced;
2Vrms unbalanced |
| Output Volume |
-80 to +20 dB level adjustment range plus Mute |
| Mute |
Enable or disable independently for HDMI and analog audio output |
| Analog Output Performance |
Frequency Response: 20 Hz to 20 kHz ±0.5 dB
S/N Ratio: >95 dB @ 10 dBV, 20 Hz to 20 kHz, A-weighted
THD+N: <0.005% @ 1 kHz and 10 dBV
Stereo Separation: 20 Hz to 20 kHz ≤80 dB |
| Communications |
| Ethernet |
100/1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, CIP, DHCP, web browser setup and control |
| RS-232 |
2-way device control and monitoring up to 115.2k baud with hardware and software handshaking |
| IR |
1-way device control via infrared up to 60 kHz |
| HDMI |
HDCP 2.2, EDID, CEC |
| DM Essentials |
HDCP 2.2, EDID |
| Connectors |
| HDMI INPUT 1 |
(1) HDMI Type A connector, female;
HDMI digital video/audio inputs;
DVI and Dual-Mode DisplayPort interface compatible2 |
| DM INPUT 2 |
(1) 8-pin RJ-45 yellow connector, female, shielded;
DM Essentials input port for connection to a DM Essentials transmitter |
| HDMI OUTPUT |
(1) HDMI Type A connector, female;
HDMI digital video/audio output;
DVI compatible3
NOTE: CEC over the HDMI output provides Power On/Off control of the display device without a control system or full programmable control of any device with a control system.
|
| AUDIO L/R |
(1) 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Maximum Output Level: 4Vrms balanced, 2Vrms unbalanced;
Output Impedance: 200 Ω balanced, 100 Ω unbalanced |
| Ethernet |
(1) 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port |
| I/O 1-2 |
(2) 2-pin detachable terminal blocks;
Comprised of 2 Versiport digital input/output or analog input ports (referenced to GND);
Digital Input: Rated to 0-24VDC, input impedance 20 kΩ, logic threshold >3.125V low/0 and <1.875 V high/1;
Digital Output: 250mA sink from maximum 24VDC, catch diodes for use with real world loads;
Analog Input: Rated for 0-10VDC, protected to 24VDC maximum, input impedance 21 kΩ with pull-up resistor disabled;
Programmable 5V, 2 kΩ pull-up resistor per pin
|
| RELAY 1-2 |
(2) 2-pin detachable terminal blocks;
Comprised of 2 normally open, isolated relays;
Rated 1A, 30VAC/VDC;
MOV arc suppression across contacts |
| IR |
(1) 2-pin 3.5 mm detachable terminal block;
IR output control port; supports IR up to 60 kHz;
IRP2 emitter sold separately
NOTE: The IR port provides Power On/Off control of the display device with the use of a control system.
|
| COM |
(1) 5-pin 3.5 mm detachable terminal block;
Bidirectional RS-232 port;
Supports RS-232 up to 115.2k baud with hardware and software handshaking
NOTE: The COM port provides Power On/Off control of the display device without a control system or full programmable control of any device with a control system.
|
| 24V 1.25A |
(1) 2.1 x 5.5 mm DC power connector;
24VDC power input;
PW-2412WU power pack included
NOTE: The power pack powers both the HD‑RX‑4K-210-C-E and the connected DM Essentials transmitter. A power pack must not be connected to both devices simultaneously.
|
| SERVICE |
(1) USB Type A connector, female;
For factory use only |
| Controls and Indicators |
| PWR |
(1) bicolor green/amber LED, indicates that power is being applied to the HD‑RX‑4K-210-C-E from the power pack connected to either the HD‑RX‑4K-210-C-E or the transmitter;
Amber indicates that the HD‑RX‑4K-210-C-E is booting;
Green indicates that the HD‑RX‑4K-210-C-E is operational |
| INPUT 1-2 |
(2) Push buttons for manual input selection and (2) bicolor green/amber LEDs;
Green indicates that video is switched;
Amber indicates that video is detected but is not switched |
| AUTO |
(1) Push button to enable or disable automatic switching, and (1) green LED to indicate that automatic switching is enabled |
| SETUP |
(1) Red LED and (1) push button for display of IP address on the HDMI output |
| DM Essentials |
(2) LEDs on RJ-45 connector;
Green indicates that a DM Essentials link is established;
Flashing amber indicates non-HDCP video and solid amber indicates HDCP video |
| Ethernet |
(2) LEDs on RJ-45 connector;
Green indicates that an Ethernet link is established;
Flashing amber indicates Ethernet activity |
| Power |
| Power Pack (Included) |
Input: 100-240 VAC, 50/60 Hz
Output: 1.25 A @ 24 VDC
Model: PW-2412WU
NOTE: The power pack powers both the HD‑RX‑4K-210-C-E and the connected DM Essentials transmitter. A power pack must not be connected to both devices simultaneously.
|
| Power Consumption |
9 W typical |
| Environmental |
| Temperature |
32° to 104°F (0° to 40°C) |
| Humidity |
10% to 90% RH (noncondensing) |
| Heat Dissipation |
30.7 BTU/hr |
| Acoustic Noise |
Not applicable (fanless) |
| Construction |
| Chassis |
Metal, black finish, vented sides, 2 mounted flanges attached |
| Mounting |
Surface or rack rail mount |
| Dimensions |
| Height |
5.11 in. (130 mm) |
| Width |
10.53 in. (268 mm) with mounting flanges attached |
| Depth |
1.10 in. (28 mm) |
| Replace this text (if this line is necessary) |
| Weight |
| 2.3 lb (1.05 kg) |
| Compliance |
|
Regulatory Model: M1845001
UL® Listed for US and Canada, CE, IC, FCC Part 15 Class B digital device
|