4 Channel Electronic Low-Voltage Dimmer Module, Single Feed - International Version, 230V
This product has been discontinued. Please contact Crestron True Blue Support at 1-888-CRESTRON for a replacement solution or more information.
Provides 4 channels of dimming for 230V electronic low-voltage and incandescent loads. Each channel is rated for 2300 Watts, with a total module rating of 2990 Watts. Air-gap relays are provided on every channel output to allow individual circuits to be serviced without disabling the entire module.
Visit the Crestron® Lighting Fixture Compatibility page to find out which Crestron lighting devices have been tested and are compatible with third party lighting fixtures.
As part of a complete Crestron lighting system, the CLXI-1DELV4 lighting control module provides 4 channels of dimming for 230V electronic low-voltage and incandescent loads. Each channel is rated for 2300 Watts, with a total module rating of 2990 Watts. Air-gap relays are provided on every channel output to allow individual circuits to be serviced without disabling the entire module.
CLXI-Series dimmers are rigorously built using oversized heat sinks for ultimate reliability. Split-bobbin transformers and ground-referenced electronics deliver superior performance. Lamp flicker is minimized through Crestron's innovative zero-crossing detection technique, backed by proprietary firmware. Low-maintenance convection cooling assures quiet and trouble-free operation.
An override feature allows each channel to be adjusted to a preset state during setup. In the event that Cresnet® communications should be disrupted for any reason, a simple contact closure can be used to activate the override presets.
The CLXI-1DELV4 occupies a single module space in any CAEN or CAENIB automation enclosure. Termination of high-voltage wiring to the module is facilitated by a CLTI-1DELV4 terminal block, sold separately to enable termination of the wiring at any time prior to installing the module. CLXI modules are controlled by the PAC2 and PAC2M professional automation control systems via the Cresnet network. A 5-wire link provides bussing of the Cresnet and override signals between modules within an enclosure (interconnect jumpers included).
| Load Ratings |
| |
Dimmer Channels |
4 |
| |
Per Channel |
10 Amps (2300 Watts) |
| |
Module Total |
13 Amps (2990 Watts) |
| |
Load Types |
Electronic Low-Voltage, Incandescent |
| |
Minimum Load |
15 Watts |
| Power Requirements |
| |
230 Volts AC, 50/60Hz, single-phase |
| Connectors on Module |
| |
Module Interconnect |
(2) 5-pin 0.156 inch headers;
Cresnet/Override interconnect ports;
Connect to PAC2, PAC2M, CAEN-BLOCK, or adjacent CLXI-Series module using interconnect cable provided |
| Connections via CLTI or CLTIBN Terminal Block (Sold Separately) |
| |
LINE |
(1) DIN rail terminal block, brown, line power input |
| |
DIM 1 - 4 |
(4) DIN rail terminal blocks, red, channel outputs |
| |
N IN |
(1) DIN rail terminal block, blue, line input neutral |
| |
N OUT 1 - 4 |
(4) DIN rail terminal blocks, blue, channel output neutrals |
| Buttons |
| |
SETUP |
Used for manual channel activation and TSID |
| LED Indicators |
| |
PWR |
(1) Green LED, indicates line power is applied to the LINE terminal |
| |
NET |
(1) Yellow LED, indicates communication with the control system |
| |
1 – 4 |
(4) Red LEDs, each indicates the state of the corresponding channel |
| |
SETUP |
(1) Red LED, indicates unit is in setup/manual mode |
| Environmental |
| |
Temperature |
32° to 104° F (0° to 40° C) |
| |
Humidity |
10% to 90% RH (non-condensing) |
| |
Heat Dissipation |
117 BTU/Hr at maximum load |
| Enclosure |
| |
Gray metal with black heat sink, surface mount module with (2) integral mounting flanges;
Occupies 1 module space in any CAEN or CAENIB enclosure |
| Dimensions |
| |
Height |
7.59 in (193 mm) |
| |
Width |
6.92 in (176 mm) |
| |
Depth |
3.43 in (87 mm) |
| Weight |
| |
3.00 lbs. (1.36 kg) |
Click
here to search product certificates.
Please select your region below to see the appropriate Advertised Pricing.