4 Channel Motor Control Module, 1 Feed, 120V
Provides four channels of motor control for 120 Volt residential lighting applications. Supports 3-wire bidirectional motors for drapes, blinds, projection screens, and lifts. Installs in a CAEN or CAEN-MLO wall mount automation enclosure as part of a complete Crestron® centralized lighting control system.
For commercial lighting applications, please visit www.crestronlighting.com.
The Crestron® CLX-1MC4 is a four-channel, single-feed motor control module designed for 120V lighting system applications. It installs in a CAEN or CAEN-MLO enclosure and provides control of bidirectional motors for drapes, blinds, projection screens, lifts, and other equipment. Each channel is rated for 10 Amps or 1/2 HP, with a total module rating of 16 Amps.
Centralized Lighting Cabinet Installation
Crestron CLX series lighting control modules are designed to be installed in a CAEN or CAEN-MLO wall mount enclosure. Available in a variety of sizes, CAEN and CAEN-MLO enclosures provide a scalable, high-density centralized lighting control solution for any-sized residence. A selection of CLX module types is offered to accommodate a wide range of load types and system configurations.
Termination of high-voltage wiring to the CLX-1MC4 module is facilitated using a CLT-1MC4 terminal block, which is sold separately to enable termination of the wiring prior to installing the module. This terminal block mounts beside the module within the enclosure. Low-voltage control signals are bussed between each of the modules within an enclosure via a simple 5-wire link (interconnect jumpers included), which terminates to a single terminal block (model CAEN-BLOCK, sold separately) at the bottom of the enclosure.
Cresnet® Communications
The CLX-1MC4 interfaces with a Crestron control system (a.k.a., control processor or automation processor) via Cresnet. Cresnet is a simple 4-wire network bus that provides the communications backbone for a system of Crestron motor controllers, dimmers, switches, keypads, shades, thermostats, and other devices.
Key Features
- Four-channel motor control module for residential lighting applications
- Installs in a Crestron® CAEN or CAEN-MLO enclosure
- Supports open/close or up/down control of 3-wire bidirectional motor loads up to 1/2 HP each
- Rated 10 Amps per channel, 16 Amps total, at 120 Volts AC
- Crestron system integration via Cresnet®
- Easy termination using a CLT-1MC4 terminal block (sold separately)
Load Control |
|
Motor Control Channels |
4 |
|
Load Types |
3-wire bidirectional motors |
|
Per Channel Load Rating |
10 Amps, 1/2 HP |
|
Module Total Load Rating |
16 Amps |
|
Line/Load Voltage |
120 Volts AC, 60 Hz; requires one single-phase feed |
Connections |
|
Via Terminal Block (sold separately) |
LINE: (1) Screw terminal, black, line power feed input;
OPEN 1 – 4: (4) Screw terminals, red, "open" control outputs (per channel);
CLOSE 1 – 4: (4) Screw terminals, blue, "close" control outputs (per channel);
N IN: (1) Screw terminal, white, line power feed neutral;
N OUT 1 – 4: (4) Screw terminals, white, load neutrals (per channel);
Note: Each terminal accepts one 14-10 AWG wire. |
|
Module Interconnect |
(2) 5-pin 0.156 inch headers;
Cresnet/Override interconnect ports;
Each connects to the adjacent module using the interconnect jumper provided;
Connects to a CAEN-BLOCK (sold separately) when installed in the lowest position within the enclosure |
Controls & Indicators |
|
PWR |
(1) Green LED, indicates line power is applied to the LINE terminal |
|
NET |
(1) Yellow LED, indicates Cresnet communication with the control system |
|
SETUP |
(1) Pushbutton and (1) red LED, used to enter Local mode and test each channel |
|
1 – 4 |
(8) Red LEDs, each indicates the open or closed status of the corresponding channel |
Environmental |
|
Temperature |
32° to 104° F (0° to 40° C) |
|
Humidity |
10% to 90% RH (non-condensing) |
|
Heat Dissipation |
15 BTU/hr + (0.44 BTU/hr x Load Current in Amps);
22 BTU/hr at maximum load |
Enclosure |
|
Gray metal with black heat sink, surface mount module with (2) integral mounting flanges;
Occupies 1 module space in a CAEN or CAEN-MLO enclosure |
Dimensions |
|
Height |
7.59 in (194 mm) |
|
Width |
6.92 in (176 mm) |
|
Depth |
3.43 in (87 mm) |
Weight |
|
3.00 lb (1.36 kg) |
Compliance |
|
UL Listed for US & Canada |
Click
here to search product certificates.
Please select your region below to see the appropriate Advertised Pricing.